There is a problem with my spiritism in Naruto

As the metal fragments melted, Xiaobai felt that the connection between his clone and those fragments became much weaker.

Fortunately, although it was much downplayed, Xiaobai could still see the properties of these melted metal fragments through the feedback from the analyzer.

After being tempered again, the metal fragments regained their toughness.

And under its constantly floating attributes, the clone also saw an additional attribute.

Chakra assimilation rate: 80

Will the chakra metal that has been assimilated by himself begin to lose chakra after it stops injecting chakra? Xiaobai thought in his mind.

As it is heated in the furnace, this assimilation rate is still decreasing.

Finally, when the metal fragments were completely melted away, the chakra assimilation rate was maintained at 40.00%.

But what is gratifying is that the reprocessed chakra metal seems to retain the remaining chakra, stabilizing at 40.00% and then no longer changing.

The metal tray was pulled out of the furnace, and a special mold was quickly placed on it to fix the molten iron in the mold.

As the analyzer cooled, a long blue metal strip only as long as a white little finger appeared on the tray.

After reaching out and picking up the metal bar, Xiaobai put it in front of his eyes and observed it carefully.

The silver-white metal surface still carries a slight wind sound that can be heard with the ears. After the clone picks it up, he can also feel a small breeze stirring his hair.

What's a little strange is that the chakra contained in it seems to have changed its nature after being assimilated, and the clone no longer has that sense of affinity as if it were part of his own body.

It's kind of weird.

The clone put the piece of chakra metal aside and then continued to look at the twisted knife strip in front of him.

In order to ensure that the original data of the two steel bars would not change, the small hammer on the analyzer was hammered for a while before being put back into the furnace for tempering.

Finally, after twenty minutes, the two red steel bars were still twisted together.

After blending the two steel bars together, the clone began to control the small steel hammer to beat the entire knife bar longer.

Whether it is District [-] in the real world or the world of Naruto, these samurai and ninjas do not wear metal armor.

Although the texture of the armor on the clone looks very much like metal, you can still hear a crisp sound after tapping it gently with your hand.

After knowing the texture of the armor, Xiaobai, who did not need to consider the armor-breaking effect at all, chose the half-blade production method without hesitation.

Different from the weapons in ancient my country, the swords of District [-], which are specially used for cutting meat, all have one thing in common, that is, their blade width is very high.

Whether it is a katana or a tachi, the ratio of blade to blade will be at least 1:1, and some knives that pursue extreme sharpness will even be even more exaggerated.

This is the so-called half-blade.

Although this amplified sharpness is terrifying in terms of sharpness, it also sacrifices the sturdiness of the entire blade.

To put it simply, if you use this kind of knife to cut metal armor, the wear and tear of the entire weapon will be very terrifying.

The struck blade quickly began to deform, and the stretched, slender and narrow blade was soon cut into pieces in a ratio of seven to three.

The long blade was quickly cooled and set aside, and the short blade was heated and beaten again.

The clone reached out and picked up the longer knife blade.

Although the blade looks gray, its cross-section has a very beautiful pattern.

After checking one side and finding that there were no gaps in the entire blade, the clone returned his attention to the iron felt.

During the rapid tapping, the already thin knife blade was stretched again, and at the same time, an iron drill began to drill holes in the deliberately thinned knife handle.

Finally, after the entire blade was struck to the width of Xiaobai's knuckle, the metal hammer slowly stopped.

The seal carving knife began to slowly divide the bleeding groove at the lower part of the back of the knife, and many small lines were separated into the blood groove.

The red steel looks extremely beautiful along with the lines carved by the seal carving knife. It feels like a landscape painting painted by Western oil paints.

Little bits of water mist are sprinkled out, slowly cooling the blade. At the same time, the analyzer begins to use a whetstone to polish the blade on the blade.

Because of the current shortage of tools, Xiaobai could only choose this fine sharpening stone to polish the blade.

Seeing a natural whetstone being used to polish the knife blank like this, Xiaobai felt his heart bleed.

While waiting for the polishing to be completed, Xiaobai controlled the clone and returned to the ground to find a whole piece of wood.

After placing the whole wood into the analyzer, the water mist was sprinkled again to further cool down the weapon, which was still at a relatively high temperature.

The part of the handle that was cooled first was quickly covered with polished logs and wooden rivets were inserted.

The Sword God, which still retained its warmth, gradually took shape under the rapid grinding of the grindstone.

Okay, now try adding chakra metal to it and see if it has any effect.

A mechanical arm stretched out from the analyzer and collected the chakra metal into it. Then a small pen-like needle began to fill in and melt the lines carved in advance in the blood tank according to Xiaobai's will. of molten metal.

Xiaobai looked nervously at the changes in the properties of chakra metal in the perspective.

After being melted and filled into these grooves, the chakra metal value, which had originally dropped to forty, dropped again.

Fortunately, this decline finally stopped at around 20.00% and stopped changing.

An hour later, the clone picked up the finished product and put it in front of him to observe it carefully.

The silver-white blade has many small lines on it, and the twisted lines on the side of the blade are even more obvious.

Because it is made of two different steel materials, the blade of the entire tachi is not a line, but has a slight wave.

On the blood tank, the chakra metal containing chakra glows slightly blue, and the small text on it looks particularly artistic.

Controlling the clone and holding the handle of the knife with one hand, the clone tried to swing the sword in his hand.

zizi~

A harsh sound that was not the sound of breaking wind sounded as the clone waved.

After hearing this harsh sound, Xiaobai suddenly said with joy: Sure enough, these seal words are effective.

With this thought, the clone once again changed the chakra in his body into wind attribute.

In this swing, Xiaobai controlled the clone to deliberately drive the chakra on his body to flow into the blade. At the same time, the clone swung out the blade.

唰

After a slight sound, a small knife mark appeared on the far wall.

what

Seeing the scar, the clone ran over quickly.

After carefully touching the beheading marks on the wall with his hand, the clone compared it with the tachi in his hand.

The scars on the wall exactly match the blade in his hand